Ultra Exterior Paint

Ultra Exterior Paint

Pittsburgh Paints & Stains Ultra exterior paint & primer in-one delivers solid all-around performance that will withstand harsh weather and still look beautiful.

Features

  • 100% acrylic latex formula for very good adhesion to multiple substrates
  • Paint & primer in-one for excellent hide and coverage
  • Provides a mildew-resistant coating for lasting beauty
  • Low temperature application down to 35°F extends the painting season
  • Resists cracking and peeling to maintain appearance

Where to use

  • Exterior Surfaces
  • Wood
  • Brick
  • Masonry
  • Aluminum
  • Concrete
  • Ferrous metal

Details

Area Preparation: Paint only clean, dry, and sound surfaces. Remove all loose, peeling paint, dirt, mildew, grease, chalk, rust and any other surface contaminants. Putty all nail holes and caulk all cracks and open seams. Sand all glossy, rough and patched surfaces. When Ultra Exterior Paint is applied to an uncoated substrate, or to bare wood, two coats are required, with the first coat acting as the primer. For metal, tannin staining woods, fresh concrete or masonry or chalky surfaces, an appropriate high-quality specialty primer is recommended for best results.

If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. 

Before you start, find out how to protect yourself and your family by contacting the USEPA National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation.

Application: Stir thoroughly. Apply with a high quality brush, roller, paint pad or by spray equipment. When using more than one container of the same color, intermix to ensure color uniformity. No thinning is usually required. If necessary, thin with up to 1/4 pint (118 mL) of water per U.S. gallon (3.78 Liters) of paint.

Application Temperature: Apply when air and surface temperatures are 35°F (2°C) or above and surface is at least 5°F (3°C) above the dew point. Air and surface temperatures must remain above 35°F (2°C) for the next 24 hours.

Drying Time: Normally dries to touch in one hour at 77°F (25°C) and 50% relative humidity. Allow four hours before recoating. Drying times listed may vary depending on temperature, humidity, color, and air movement. 

Cleanup: Clean tools and hands with warm, soapy water.

Sizes & Datasheets

Product Code Finish Size MSDS
41-510 Flat Quart, One Gallon, Five Gallon MSDS
41-515 Flat Quart, One Gallon, Five Gallon MSDS
41-516 Flat Quart, One Gallon, Five Gallon MSDS
41-517 Flat Quart, One Gallon, Five Gallon MSDS
41-545 Flat Quart, One Gallon, Five Gallon MSDS
41-610 Satin Quart, One Gallon, Five Gallon MSDS
41-615 Satin Quart, One Gallon, Five Gallon MSDS
41-616 Satin Quart, One Gallon, Five Gallon MSDS
41-617 Satin Quart, One Gallon, Five Gallon MSDS
41-645 Satin Quart, One Gallon, Five Gallon MSDS
41-710 Semi-Gloss Enamel Quart, One Gallon, Five Gallon MSDS
41-715 Semi-Gloss Enamel Quart, One Gallon, Five Gallon MSDS
41-716 Semi-Gloss Enamel Quart, One Gallon, Five Gallon MSDS
41-717 Semi-Gloss Enamel Quart, One Gallon, Five Gallon MSDS
41-745 Semi-Gloss Enamel Quart, One Gallon, Five Gallon MSDS