Paramount™ Exterior Paint

Paramount™ Exterior Paint

It’s not just paint, it’s Paramount.

Paramount is designed to exceed your performance expectations.  It’s the perfect blend of cutting edge paint & color technology and style expertise – the most advanced protection you can get in true one coat coverage with exceptional stainblocking and hiding.


  • Super Premium Paint & Primer in One
  • Delivers True One Coat Coverage
  • Exceptional Adhesion to Resist Cracking & Peeling
  • UV Protection Ensures True, Lasting Color
  • Provides a Durable & Washable Protective Shield

Where to use

Ideal for use on properly prepared exterior wood, brick, masonry, concrete, weathered aluminum, weathered vinyl siding, and primed metal substrates. Vinyl siding and similar plastic composites should not be painted with a color darker than the original color. Painting vinyl siding or plastic composites with a darker color may cause them to warp.


Area Preparation: Surface must be clean and dry. Remove all loose, peeling paint, dirt, mildew, grease, oil, chalk, rust, and any other surface contaminants. Repair all moisture problems. Blistering and peeling issues are commonly caused by moisture behind the paint film. Putty all nail holes and caulk all cracks and open seams. Sand all glossy, rough and patched surfaces. When Paramount Paint + Primer in One exterior paint is applied to an uncoated substrate or to bare wood, two coats are required with the first coat acting as the primer. For metal, tannin staining woods, fresh concrete or masonry (less than 30 days cure), or chalky surfaces, use of the appropriate high quality specialty primer is recommended for best results. WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA National Lead Information Hotline at 1 -800 -424 -LEAD or log on to Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation.

Application: Stir thoroughly. Apply with a high quality brush, roller or by spray equipment. When using more than one container of the same color, intermix to ensure color uniformity. Thinning is not usually required.

Application Temperature: Apply only when air, surface, and product temperatures are above 35°F (2°C) and at least 5°F (3°C) above the dew point. Air and surface temperatures must remain above 35°F (2°C) for the next 48 hours. Do not apply late in the day when dew and condensation are likely to form or if rain or snow is expected. On large expanses of metal, temperatures must be 50°F (10°C) or higher.

Drying Time: Normally dries to touch in 30 minutes at 77°F (25°C) and 50% relative humidity. Allow 4 hours before recoating. At 35°F (2°C), dries to touch in 3 to 6 hours; allow 24 hours before recoating. Drying times listed may vary depending on temperature, humidity, color, film build, and air movement.

Cleanup: Clean tools with warm, soapy water.

Paramount Paint - Most Advanced Protection

Sizes & Datasheets

Product Code Finish Size TDS SDS
37-2510 Flat Quart, One Gallon, Five Gallon TDS SDS
37-2515 Flat Quart, One Gallon, Five Gallon TDS SDS
37-2517 Flat Quart, One Gallon, Five Gallon TDS SDS
37-2610 Satin Quart, One Gallon, Five Gallon TDS SDS
37-2615 Satin Quart, One Gallon, Five Gallon TDS SDS
37-2617 Satin Quart, One Gallon, Five Gallon TDS SDS
37-2710 Semi-Gloss Quart, One Gallon, Five Gallon TDS SDS
37-2715 Semi-Gloss Quart, One Gallon, Five Gallon TDS SDS
37-2717 Semi-Gloss Quart, One Gallon TDS SDS