Pittsburgh Paints & Stains ULTRA Advanced Solid Color Stain is a premium quality wood stain and sealant in one product. Rich, opaque color hides signs of aging while allowing the natural texture of wood to show, making it ideal for older wood. A self-priming, 100% acrylic stain, Ultra Advanced solid color stain delivers excellent protection from the elements. Ultra Advanced stain also comes with a satisfaction guarantee.
- Wood Stain and Sealant in One
- Advanced Two-Way Waterproofing Protection
- Ultra UV Premium Protection Guards Against Sun Damage
- After Staining, Wooden Surface Will be Rain Ready in Just 8 Hours
- Low Temperature Application Down to 35°F
- Provides a Dual-Action Mold and Mildew Resistant Coating
- Exclusive Scuff Guard® Protection Shields Against Scuffing and Abrasions
Surface must be clean, dry and free of all dust, dirt, mildew, oil, loose wood fibers and other contaminants. Remove loose, peeling stain or paint by sanding, scraping or wire brushing. Use an exterior wood cleaner to prepare new wood prior to coating, and to clean and restore weathered, dirty surfaces and remove mildew stains. After rinsing, allow wood to dry. WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA National Lead Information Hotline at 1-800-424‑LEAD or log on to www.epa.gov/lead. Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation.
DO NOT THIN. Stir thoroughly and often during use. Apply to a small area and allow to dry to ensure acceptable appearance. Intermix containers to ensure color uniformity. Apply two thin coats with a high quality brush, roller, paint/stain pad or by spray equipment. When rolling or spraying, always back-brush for best results. Some colors, or a drastic color change may require an additional coat to achieve a uniform finish. To help avoid lap marks, apply to only a few boards at a time, and maintain a wet edge.
Apply when no precipitation is expected for 24 hours, and when air and surface temperatures are 35°F to 90°F (2°C to 32°C) and will remain above 35°F (2°C) for the next 24 hours. Avoid staining in direct sunlight or on hot surfaces.
Normally dries to touch in 30 minutes when applied in temperatures of 50°F (10°C) to 85°F (29°C). Allow 2 to 4 hours between coats or before recoating. High humidity or low temperature application may prolong drying and recoating times. Allow 24 to 48 hours of drying time for light foot traffic or furniture placement. Newly stained surfaces should be allowed to cure 30 days before washing.
Approximately 350 to 500 sq. ft. (32.5 to 46.5 sq. meters) per gallon (3.78 Liters) depending on application, wood texture and porosity.
Clean brushes and tools with warm, soapy water.
|41-2701||Stain - Tint Base||Quart/946 mL (04), Gallon/3.78 L (01), 1/2 Pint/236 mL (16), 5 Gallons/18.9 L (05)|
|41-2702||Stain - Tint Base||Gallon/3.78 L (01), 1/2 Pint/236 mL (16), Quart/946 mL (04), 5 Gallons/18.9 L (05)|
|41-2703||Stain - Tint Base||Gallon/3.78 L (01)|
|41-2704||Stain - Custom Color||Gallon/3.78 L (01)|
|41-2705||Stain - Custom Color||Gallon/3.78 L (01)|
|41-2706||Stain - Custom Color||Gallon/3.78 L (01)|